I don't see signals or trades with my MTNTF7 strategy

MTNTF7 No Results 

in 99% of all cases this is due to not understanding or configuring the Trade Setup mode and Trade Entry - 2 Phase Signals indicators and how they are used inside a strategy - it is vital to follow the guidance or you will find it very hard or easy accordingly: 
N.B. It is the Indicator signal that causes the signals - the strategy merely listens for and executes the signals according to the the settings for Order Type - then manages the trade -with no spark/signal nothing is fired the engine wont work... so you will get no results if you have no spark/signal. 
...Once you understand the principle of one signals indicator and one strategy you will find all are 90% the same with only a difference of indicator and signal logic...

PLEASE READ AND ANSWER BELOW IF STUCK 
The 4 Steps to get Signals on a chart , Backtest or Optimise any MTNTF7 Strategy

Please can you verify or follow the guidance below so we are on the same page and understand the basic concepts for all Strategies in the MTNTF7: 
STEP #1 . you read and viewed the Signals Indicators, guidance to learn about the Trade Setup, Entry and common parameters to all signals indicators and you have successfully used the MT Signals Scalper in isolation on a chart by itself and learned to configure the Trade Setup and Entry modes 
https://microtrends.zendesk.com/entries/59737249-Getting-Started-with-MicroTrends-NinjaTrader-Framework-Signals-Indicators

STEP #2 . TIP!!!: You have understood the caveats of Zone Setting Id - and have taken care to set the ID to 0 is using settings and altering them 
https://microtrends.zendesk.com/entries/68480125-Zone-Setting-ID-Saving-and-loading-your-own-settings-for-MTNTF7-Indicators-and-strategies

STEP #3. To understand the Step 1,2 and used them in a strategy - using the same chart as #1 - you will need to remove the indicator -then connect to a datafeed- now you right click the chart > select Strategies > Select MT Scalper > and add it to the chart . Use the settings in step #1 and configure these into the Signals Section for the Strategy Signals Scalper Indicator -so that signals are produced inside the strategy - 
https://microtrends.zendesk.com/entries/53195949-Getting-started-with-MicroTrends-NinjaTrader-Framework-Strategies

STEP #4 Strategy Chart Walkthrough and Strategy Analyzer 
A. use in Sim Mode - Sim 101 on a chart in realtime - or historically - then the problem may be the account has to be SIM101 not a demo account 
B. with the optimiser or backteser setting i will Show it works

PLEASE WATCH THIS Video - Scalper how to Back Test - Quick Example to show how to go from the chart to the Strategy Analyzer etc 
http://screencast.com/t/W4CAUytmtDC1

Signals and Stats 
in terms of backtesting on a chart -set the general parameters as shown here: 
http://screencast.com/t/SdRM0pVNP

TIP: . Once you have mastered how to get signals on a chart - then you can experiment with the Optimiser etc

Diagnosing Summary and more help 
*************************************************************************************** 
Please say what you are able to do/ 
1. Add the MT Siganls Scalper Indicator on to a chart and see/configure signals - YES/NO 
2. Add the MT Scalper Strategy to a chart and enable it on a "sim101" account with Signals On - and see visual signals & trades - YES/No 
3. Use the Strategy Analyzer and backtest YES/NO 
4. You can view trades in realtime -but not historically - do you have Historical Trading On? What parmeters do you have on/off? 
5. You followed the guidance 1 to 4 - and watched video: http://screencast.com/t/W4CAUytmtDC1 - please say what steps you could do and could not do. 
***************************************************************************************

Please provide the steps you are taking so we can replicate your scenario 
You open a chart - connect to NT - select the MT Scalper Strategy - Add it to the Chart...etc

Please provide a screenshot of your settings used in the strategy - free tool https://www.techsmith.com/jing.html

MicroTrends Support 
support@microtrends.co 
http://www.microtrends.co/support/

Tip! You can visit the help desk forum to see previous answered frequently asked questions: 
http://microtrends.zendesk.com/forums